cu(1) General Commands Manual cu(1)
NAME
cu - Call up another system
SYNOPSIS
cu [ options ] [ system | phone | "dir" ]
DESCRIPTION
The cu command is used to call up another system and act as a dial in
terminal. It can also do simple file transfers with no error checking.
cu takes a single argument, besides the options. If the argument is
the string "dir" cu will make a direct connection to the port. This
may only be used by users with write access to the port, as it permits
reprogramming the modem.
Otherwise, if the argument begins with a digit, it is taken to be a
phone number to call. Otherwise, it is taken to be the name of a sys-
tem to call. The -z or --system option may be used to name a system
beginning with a digit, and the -c or --phone option may be used to
name a phone number that does not begin with a digit.
cu locates a port to use in the UUCP configuration files. If a simple
system name is given, it will select a port appropriate for that sys-
tem. The -p, --port, -l, --line, -s and --speed options may be used to
control the port selection.
When a connection is made to the remote system, cu forks into two pro-
cesses. One reads from the port and writes to the terminal, while the
other reads from the terminal and writes to the port.
cu provides several commands that may be used during the conversation.
The commands all begin with an escape character, initially ~ (tilde).
The escape character is only recognized at the beginning of a line. To
send an escape character to the remote system at the start of a line,
it must be entered twice. All commands are either a single character
or a word beginning with % (percent sign).
cu recognizes the following commands:
~. Terminate the conversation.
~! command
Run command in a shell. If command is empty, starts up a shell.
~$ command
Run command, sending the standard output to the remote system.
~| command
Run command, taking the standard input from the remote system.
~+ command
Run command, taking the standard input from the remote system and
sending the standard output to the remote system.
~#, ~%break
Send a break signal, if possible.
~c directory, ~%cd directory
Change the local directory.
~> file
Send a file to the remote system. This just dumps the file over
the communication line. It is assumed that the remote system is
expecting it.
~< Receive a file from the remote system. This prompts for the local
file name and for the remote command to execute to begin the file
transfer. It continues accepting data until the contents of the
eofread variable are seen.
~p from to, ~%put from to
Send a file to a remote Unix system. This runs the appropriate
commands on the remote system.
~t from to, ~%take from to
Retrieve a file from a remote Unix system. This runs the appro-
priate commands on the remote system.
~s variable value
Set a cu variable to the given value. If value is not given, the
variable is set to true.
~! variable
Set a cu variable to false.
~z Suspend the cu session. This is only supported on some systems.
On systems for which ^Z may be used to suspend a job, ~^Z will
also suspend the session.
~%nostop
Turn off XON/XOFF handling.
~%stop
Turn on XON/XOFF handling.
~v List all the variables and their values.
~? List all commands.
cu also supports several variables. They may be listed with the
~v command, and set with the ~s or ~! commands.
escape
The escape character. Initially ~ (tilde).
delay
If this variable is true, cu will delay for a second after recog-
nizing the escape character before printing the name of the local
system. The default is true.
eol The list of characters which are considered to finish a line. The
escape character is only recognized after one of these is seen.
The default is carriage return, ^U, ^C, ^O, ^D, ^S, ^Q, ^R.
binary
Whether to transfer binary data when sending a file. If this is
false, then newlines in the file being sent are converted to car-
riage returns. The default is false.
binary-prefix
A string used before sending a binary character in a file trans-
fer, if the binary variable is true. The default is ^V.
echo-check
Whether to check file transfers by examining what the remote sys-
tem echoes back. This probably doesn't work very well. The de-
fault is false.
echonl
The character to look for after sending each line in a file. The
default is carriage return.
timeout
The timeout to use, in seconds, when looking for a character, ei-
ther when doing echo checking or when looking for the echonl char-
acter. The default is 30.
kill The character to use delete a line if the echo check fails. The
default is ^U.
resend
The number of times to resend a line if the echo check continues
to fail. The default is 10.
eofwrite
The string to write after sending a file with the ~> command. The
default is ^D.
eofread
The string to look for when receiving a file with the ~< command.
The default is $, which is intended to be a typical shell prompt.
verbose
Whether to print accumulated information during a file transfer.
The default is true.
OPTIONS
The following options may be given to cu.
-e, --parity=even
Use even parity.
-o, --parity=odd
Use odd parity.
--parity=none
Use no parity. No parity is also used if both -e and -o are
given.
-h, --halfduplex
Echo characters locally (half-duplex mode).
--nostop
Turn off XON/XOFF handling (it is on by default).
-f, --nortscts
Do not use hardware flow control.
-E char, --escape char
Set the escape character. Initially ~ (tilde). To eliminate the
escape character, use -E ''.
-z system, --system system
The system to call.
-c phone-number, --phone phone-number
The phone number to call.
-p port, --port port
Name the port to use.
-a port
Equivalent to --port port.
-l line, --line line
Name the line to use by giving a device name. This may be used to
dial out on ports that are not listed in the UUCP configuration
files. Write access to the device is required.
-s speed, --speed speed
The speed (baud rate) to use.
-# Where # is a number, equivalent to --speed #.
-n, --prompt
Prompt for the phone number to use.
-d Enter debugging mode. Equivalent to --debug all.
-x type, --debug type
Turn on particular debugging types. The following types are rec-
ognized: abnormal, chat, handshake, uucp-proto, proto, port, con-
fig, spooldir, execute, incoming, outgoing. Only abnormal, chat,
handshake, port, config, incoming and outgoing are meaningful for
cu.
Multiple types may be given, separated by commas, and the --debug
option may appear multiple times. A number may also be given,
which will turn on that many types from the foregoing list; for
example, --debug 2 is equivalent to --debug abnormal,chat. --de-
bug all may be used to turn on all debugging options.
-I file, --config file
Set configuration file to use. This option may not be available,
depending upon how cu was compiled.
-v, --version
Report version information and exit.
--help
Print a help message and exit.
BUGS
This program does not work very well.
AUTHOR
Ian Lance Taylor <ian@airs.com>
Taylor UUCP 1.07 cu(1)