PASSPHRASE-ENCODING(7SSL) OpenSSL PASSPHRASE-ENCODING(7SSL)
NAME
passphrase-encoding - How diverse parts of OpenSSL treat pass phrases
character encoding
DESCRIPTION
In a modern world with all sorts of character encodings, the treatment
of pass phrases has become increasingly complex. This manual page
attempts to give an overview over how this problem is currently
addressed in different parts of the OpenSSL library.
The general case
The OpenSSL library doesn't treat pass phrases in any special way as a
general rule, and trusts the application or user to choose a suitable
character set and stick to that throughout the lifetime of affected
objects. This means that for an object that was encrypted using a pass
phrase encoded in ISO-8859-1, that object needs to be decrypted using a
pass phrase encoded in ISO-8859-1. Using the wrong encoding is
expected to cause a decryption failure.
PKCS#12
PKCS#12 is a bit different regarding pass phrase encoding. The
standard stipulates that the pass phrase shall be encoded as an ASN.1
BMPString, which consists of the code points of the basic multilingual
plane, encoded in big endian (UCS-2 BE).
OpenSSL tries to adapt to this requirements in one of the following
manners:
1. Treats the received pass phrase as UTF-8 encoded and tries to re-
encode it to UTF-16 (which is the same as UCS-2 for characters
U+0000 to U+D7FF and U+E000 to U+FFFF, but becomes an expansion for
any other character), or failing that, proceeds with step 2.
2. Assumes that the pass phrase is encoded in ASCII or ISO-8859-1 and
opportunistically prepends each byte with a zero byte to obtain the
UCS-2 encoding of the characters, which it stores as a BMPString.
Note that since there is no check of your locale, this may produce
UCS-2 / UTF-16 characters that do not correspond to the original
pass phrase characters for other character sets, such as any
ISO-8859-X encoding other than ISO-8859-1 (or for Windows, CP 1252
with exception for the extra "graphical" characters in the
0x80-0x9F range).
OpenSSL versions older than 1.1.0 do variant 2 only, and that is the
reason why OpenSSL still does this, to be able to read files produced
with older versions.
It should be noted that this approach isn't entirely fault free.
A pass phrase encoded in ISO-8859-2 could very well have a sequence
such as 0xC3 0xAF (which is the two characters "LATIN CAPITAL LETTER A
WITH BREVE" and "LATIN CAPITAL LETTER Z WITH DOT ABOVE" in ISO-8859-2
encoding), but would be misinterpreted as the perfectly valid UTF-8
encoded code point U+00EF (LATIN SMALL LETTER I WITH DIAERESIS) if the
pass phrase doesn't contain anything that would be invalid UTF-8. A
pass phrase that contains this kind of byte sequence will give a
different outcome in OpenSSL 1.1.0 and newer than in OpenSSL older than
1.1.0.
0x00 0xC3 0x00 0xAF # OpenSSL older than 1.1.0
0x00 0xEF # OpenSSL 1.1.0 and newer
On the same accord, anything encoded in UTF-8 that was given to OpenSSL
older than 1.1.0 was misinterpreted as ISO-8859-1 sequences.
OSSL_STORE
ossl_store(7) acts as a general interface to access all kinds of
objects, potentially protected with a pass phrase, a PIN or something
else. This API stipulates that pass phrases should be UTF-8 encoded,
and that any other pass phrase encoding may give undefined results.
This API relies on the application to ensure UTF-8 encoding, and
doesn't check that this is the case, so what it gets, it will also pass
to the underlying loader.
RECOMMENDATIONS
This section assumes that you know what pass phrase was used for
encryption, but that it may have been encoded in a different character
encoding than the one used by your current input method. For example,
the pass phrase may have been used at a time when your default encoding
was ISO-8859-1 (i.e. "naieve" resulting in the byte sequence 0x6E 0x61
0xEF 0x76 0x65), and you're now in an environment where your default
encoding is UTF-8 (i.e. "naieve" resulting in the byte sequence 0x6E
0x61 0xC3 0xAF 0x76 0x65). Whenever it's mentioned that you should use
a certain character encoding, it should be understood that you either
change the input method to use the mentioned encoding when you type in
your pass phrase, or use some suitable tool to convert your pass phrase
from your default encoding to the target encoding.
Also note that the sub-sections below discuss human readable pass
phrases. This is particularly relevant for PKCS#12 objects, where
human readable pass phrases are assumed. For other objects, it's as
legitimate to use any byte sequence (such as a sequence of bytes from
`/dev/urandom` that's been saved away), which makes any character
encoding discussion irrelevant; in such cases, simply use the same byte
sequence as it is.
Creating new objects
For creating new pass phrase protected objects, make sure the pass
phrase is encoded using UTF-8. This is default on most modern Unixes,
but may involve an effort on other platforms. Specifically for
Windows, setting the environment variable "OPENSSL_WIN32_UTF8" will
have anything entered on [Windows] console prompt converted to UTF-8
(command line and separately prompted pass phrases alike).
Opening existing objects
For opening pass phrase protected objects where you know what character
encoding was used for the encryption pass phrase, make sure to use the
same encoding again.
For opening pass phrase protected objects where the character encoding
that was used is unknown, or where the producing application is
unknown, try one of the following:
1. Try the pass phrase that you have as it is in the character
encoding of your environment. It's possible that its byte sequence
is exactly right.
2. Convert the pass phrase to UTF-8 and try with the result.
Specifically with PKCS#12, this should open up any object that was
created according to the specification.
3. Do a naieve (i.e. purely mathematical) ISO-8859-1 to UTF-8
conversion and try with the result. This differs from the previous
attempt because ISO-8859-1 maps directly to U+0000 to U+00FF, which
other non-UTF-8 character sets do not.
This also takes care of the case when a UTF-8 encoded string was
used with OpenSSL older than 1.1.0. (for example, "ie", which is
0xC3 0xAF when encoded in UTF-8, would become 0xC3 0x83 0xC2 0xAF
when re-encoded in the naieve manner. The conversion to BMPString
would then yield 0x00 0xC3 0x00 0xA4 0x00 0x00, the
erroneous/non-compliant encoding used by OpenSSL older than 1.1.0)
SEE ALSO
evp(7), ossl_store(7), EVP_BytesToKey(3), EVP_DecryptInit(3),
PEM_do_header(3), PKCS12_parse(3), PKCS12_newpass(3),
d2i_PKCS8PrivateKey_bio(3)
COPYRIGHT
Copyright 2018-2020 The OpenSSL Project Authors. All Rights Reserved.
Licensed under the OpenSSL license (the "License"). You may not use
this file except in compliance with the License. You can obtain a copy
in the file LICENSE in the source distribution or at
<https://www.openssl.org/source/license.html>.
1.1.1g 2020-04-21 PASSPHRASE-ENCODING(7SSL)